Rest it on top of the valance clips. When you have positioned it the way you would like it be, press gently down so that the valance clips snap into the valance, holding it in place. Secure the blind wand. If your blinds came with a wand for opening and closing them, and it did not come pre-attached, attach it now. Karen Parziale. Take a look at the size of your windows first. If your bedroom has really big, sprawling windows, you might be better off choosing going with drapes.
Not Helpful 1 Helpful 0. Faux blinds are great! They're about 2 in 5. Not Helpful 0 Helpful 1. It depends on what the wall is made of. If it is wood, it will be very difficult. Not Helpful 4 Helpful 9.
Center support brackets can be a challenge to install. However, the method I found most success with is to apply a thin layer of gorilla glue to the backboard. Then you attach the center support bracket to the glue. Not Helpful 8 Helpful Place the end brackets onto the blinds.
Hold the blinds up to the window top where you want them to hang; mark the window top at the edges of the brackets with a pencil. Remove the two brackets from the blinds. Holding each bracket on the pencil lines, place a dot inside the bracket holes: this is where you will drill holes for the screws that hold the brackets.
Drill or nail the holes where you marked. Attach each bracket with screws, and open the brackets. Slide in the blind and close each bracket. The pull-down string should be on the right, the slot turn rod on the left. Not Helpful 7 Helpful Is it going inside of a soffit? Anyway, usually there is a track, and it snaps into the brackets.
Install the brackets and use a central point for all brackets. Hold the track with both hands put the back side in first and then clip the front end.
I find securing the right side first and then the left side next is the easiest way. Then just clip in the vertical vanes and you are good to go.
Include your email address to get a message when this question is answered. Always read the instructions provided with your blinds. Helpful 0 Not Helpful 0. Get someone to help you hold the blinds up. If you have never operated a drill, get someone who knows how to use it to help you. You Might Also Like How to. How to. Expert Interview. About This Article. Co-authored by:. The brackets, valance and other parts are thoughtfully designed to make installation easy while keeping the blinds secure and locked into place.
The key is to make sure you measure carefully before and after purchasing the blinds to make sure they fit perfectly. Installation of a single mini blind takes less than an hour, but the initial measurement should be done in advance. Make sure to take your time when measuring and double-checking measurements to avoid errors. Mini blinds can be either inside-mounted or outside-mounted.
Inside-mounting requires positioning blinds inside the window frame, so the measurements need to be exact to fit snugly. Outside-mounting is more flexible and is less likely to require custom blinds, but they also allow more light into the room due to the gap between the blinds and the window frame. Measure the inside of the window frame for its height, depth and width. The depth is only an issue in windows with very shallow frames, in which case you may need outside-mounted blinds.
Write down these measurements, refer back to them when ordering mini blinds online and keep them somewhere safe in case you need them again in the future. Most blind installation projects require the following supplies in addition to the parts included in the box:.
A cordless drill and a corded drill both work, but keep in mind, a corded drill may be a hassle if the outlets are far from the window. Attempting to drill into brick or concrete requires a special masonry drill bit, preferably with a tungsten carbide tip.
In some cases, you can install mini blinds by using adhesive strips or magnets. However, this varies depending on the specifics of the mounting system. The weight of the blinds may be too much for strips or magnets. Upon receiving the box containing your mini blinds, check its contents thoroughly to ensure it includes all the mounts, brackets, screws and other parts listed. Although a level tool is optional and can be replaced by careful measurements, it may be important if you have difficulty measuring and placing the mounts evenly on both sides.
If you have an older home, your windows may also be slightly crooked, affecting the final look of the blinds. A level tool may help you adjust to minor unevenness in the window frame, especially for outside-mounted blinds. For both inside-mounting and outside-mounting, start by measuring the proper placement for the brackets.
The directions for your specific model may specify a minimum distance from the window, so measure the depth as well as height from the windowsill. This releases the locking tab and lifts the front bracket gate so the screw holes are easily visible. Hold the prepared bracket in place and mark the screw holes with a pencil, and then repeat on the other side. Drill the holes using the electric drill, and then loosely screw in the bracket with two of the included screws. Adjust the positioning of the bracket if needed.
Repeat on the other side, and then check to make sure the blind slides into place properly. If additional support brackets are included, make sure to install those carefully as well. These are typically one to two U-shaped supports that go in the middle of the blinds to keep too much weight from hanging on the two end brackets. For blinds over 70 inches, you may need two or more support brackets. Make sure you have the required number of mounting brackets and screws. Got all the apparatus in place?
Blinds that are mounted inside the window frame create the cleanest look you can achieve, and the blinds can be made to sit as deep or shallow as you want them to. For installing the brackets inside the window frame, start by clipping the brackets on the headrail at their marked locations. Bring the headrail against the brackets in a way that the inner front edge of the headrail rests above the front end of each individual bracket.
Make sure that each bracket has been secured to the headrail.
0コメント