When working with Apache it is important to know how it will find the configuration file. You can specify a configuration file on the command line in two ways:. In both of these cases, the proper ServerRoot should be set in the configuration file. This built-in path is relative to the installation directory. Apache will then try to determine its ServerRoot by trying the following, in this order:.
If you did not do a binary install, Apache will in some scenarios complain about the missing registry key. This warning can be ignored if the server was otherwise able to find its configuration file. The value of this key is the ServerRoot directory which contains the conf subdirectory. When Apache starts it reads the httpd. If this file contains a ServerRoot directive which contains a different directory from the one obtained from the registry key above, Apache will forget the registry key and use the directory from the configuration file.
If you copy the Apache directory or configuration files to a new location it is vital that you update the ServerRoot directive in the httpd. After starting Apache either in a console window or as a service it will be listening on port 80 unless you changed the Listen directive in the configuration files or installed Apache only for the current user. To connect to the server and access the default page, launch a browser and enter this URL:.
Apache should respond with a welcome page and you should see "It Works! If nothing happens or you get an error, look in the error. If you happen to be running Apache on an alternate port, you need to explicitly put that in the URL:.
Once your basic installation is working, you should configure it properly by editing the files in the conf subdirectory. Again, if you change the configuration of the Windows NT service for Apache, first attempt to start it from the command line to make sure that the service starts with no errors.
These conflicting services include other WWW servers, some firewall implementations, and even some client applications such as Skype which will use port 80 to attempt to bypass firewall issues. Mapped drive letters allow the administrator to maintain the mapping to a specific machine and path outside of the Apache httpd configuration.
However, these mappings are associated only with interactive sessions and are not directly available to Apache httpd when it is started as a service. Use only UNC paths for network resources in httpd. Arcane and error prone procedures may work around the restriction on mapped drive letters, but this is not recommended.
When running Apache httpd as a service, you must create a separate account in order to access network resources, as described above. If more than a few dozen piped loggers are used on an operating system instance, scaling up the "desktop heap" is often necessary.
For more detailed information, refer to the piped logging documentation. Copyright The Apache Software Foundation. Licensed under the Apache License, Version 2. Customizing Apache for Windows Apache is configured by the files in the conf subdirectory. The main differences in Apache for Windows are: Because Apache for Windows is multithreaded, it does not use a separate process for each request, as Apache can on Unix.
The process management directives are also different: MaxConnectionsPerChild : Like the Unix directive, this controls how many connections a single child process will serve before exiting. Warning: The server configuration file is reread when a new child process is started. If you have modified httpd. You can install Apache as a Windows NT service as follows from the command prompt at the Apache bin subdirectory: httpd.
Never grant any network privileges to the LocalSystem account! If you need Apache to be able to access network resources, create a separate account for Apache as noted below. It is usually a good practice to grant the user the Apache service runs as read and execute RX access to the whole Apache2.
Error code is a good indication that you need to review the "Log On As" configuration for the service, since Apache cannot access a required network resource. Also, pay close attention to the privileges of the user Apache is configured to run as. Running Apache as a Console Application Running Apache as a service is usually the recommended way to use it, but it is sometimes easier to work from the command line, especially during initial configuration and testing.
To run Apache from the command line as a console application, use the following command: httpd. A fast crawlable website with a strong server is a fundamental need for SEO Performance.
Our Apache Bench load testing tutorial will be updated in light of new information over time. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. Contents hide. Author Recent Posts. Leave a Comment Cancel Reply Your email address will not be published. It can emulate browser users from eight geographical locations at once, enabling , simultaneous loadings.
It can also be used to test integrations and functionalities. On-premises and on AWS with scalability to millions of concurrent users from all geographies. Pricing is determined by Virtual User Hours consumed each month.
This framework is most commonly used for testing large numbers of tests or a large number of virtual users , though unit and integration testing can also be conducted using this framework. Performance testing software designed to verify the functionality of software under load.
Detects concurrency issues. Eclipse-based performance test tool primarily used to execute large-scale tests on server-based applications. Licensed application performance monitoring tool with local and cloud virtual agents that support most protocols. The string is sent regardless of whether the proxy needs it i.
The -q flag will suppress these messages. Default is 30 seconds. This implies a -n internally. Use this to benchmark the server within a fixed total amount of time. Per default there is no timelimit. Default table is two columns wide, with a white background.
Output The following list describes the values returned by ab : Server Software The value, if any, returned in the server HTTP header of the first successful response. If no port is given on the command line, this will default to 80 for http and for https. This will only be printed if SSL is used. Document Length This is the size in bytes of the first successfully returned document. If the document length changes during testing, the response is considered an error.
Concurrency Level The number of concurrent clients used during the test Time taken for tests This is the time taken from the moment the first socket connection is created to the moment the last response is received Complete requests The number of successful responses received Failed requests The number of requests that were considered a failure. If the number is greater than zero, another line will be printed showing the number of requests that failed due to connecting, reading, incorrect content length, or exceptions.
Write errors The number of errors that failed during write broken pipe.
0コメント